American-style drop tester. Polarity protected cables - impossible to damage unit by incorrect connection. Load applied by internal switchgear - no sparking! Suitable for 6 and 12V batteries. Applies load across cells and measures output on meter. Accurate indication of battery voltage and faulty or short circuited cell.

Tests 6 and 12V batteries. Applies load across terminals and reads voltage performance. Also checks charging voltage. Fitted with moving-coil meter. Features a pistol grip handle for ease of use.

High precision clamp meter. Conforms to EN 61010-1 CATIII 600V safety requirements for electrical equipment for measurement, control and laboratory use. Features non-contact AC voltage detection function while controls are laid out to enable use with one-hand. Includes data and maximum hold functions. Double moulded housing with soft grip case, large display for ease of use and 30mm clamp....

Compact device which accurately tests battery, cranking and alternator. No heat, no sparks and no misdiagnosis. Just key in the battery rating from the top of the battery and results are displayed on an LED control panel. No internal battery and will test batteries with a residual charge of just 7V.

Health test for 4 and 5-pin electro-mechanical relays commonly found on modern vehicles. Test feature will cycle the relay 10 times, testing the resistance, contacts and consistency within each cycle. If a cycle fails on the test then this will be indicated by a red LED and alternatively a green LED if relay works.

Fast, accurate and safe current measurement at the fuse box or battery. Ideal for fault-finding on car and commercial vehicle electrical circuits. Features large LCD display with numeric and bar-type functions. Plugs directly into the vehicle's fuse board. Supplied with mini, standard adaptors and fused crocodile clips. Compatible with alternative probes using the standard Ø4mm banana adaptors.

Durable case and integral stand suitable for the toughest workshop conditions. Large, high-contrast LCD display with 18mm high digital read-out and analogue bar graph. Includes auto-ranging, data-hold, auto-polarity, auto-power-off and low battery display functions. Bar graph simplifies lambda sensor testing. Supplied with capped test probes and K-type thermocouple.

High precision auto-ranging multimeter. Conforms to EN 61010-1 CATIII 600V safety requirements for electrical equipment for measurement, control and laboratory use. Features temperature measurement capability, max./data-hold, and auto-power-off function. Double moulded housing with soft grip case and large display for ease of use. Practical probe and lead storage and integral upright stand for...

Comprehensive set of tools for release and removal of in-car entertainment units on popular vehicles. Supplied in storage case with stamped application list for simple selection.

Enables easy removal of freewheel alternator pulley, either on or off the vehicle. Allows alternator shaft to be held while the pulley retainer is removed. Incorporates a complete range of combination TRX-Star*, spline and hex adaptors to fit most alternators. Supplied in storage case.

Designed to test low voltage glow plug operation on modern diesel engines. Prevents glow plug damage caused by testing with the vehicle battery. Glow plugs can be tested whilst in situ. Supplied in storage case with instructions. Requires 9V battery (not included).

Compact size meter with 4-digit 22mm, high-contrast LCD display and back light. Features auto-ranging, data-hold and auto-power-off functions. Includes inductive coupler (IC) for fast reading of engine rpm. Supplied with probe, crocodile clip and thermocouple leads for easy hook-up.

Professional 2-pole voltage tester CAT IV 1000V for checking high voltage on electric/hybrid vehicles. Suitable for checking AC mains and DC power supplies between 6-1000V DC and 24-1000V AC. Can also be used for checking voltage and polarity on car batteries and continuity testing of DC circuits. Includes a self-test function and illumination light. EN 61243-3, IP65, CE certified. Requires 2 x...

Ratchet crimping tool with laminated steel jaws and insulated grips. Suitable for 1.5, 2.5 and 6mm² insulated terminals. Approximately 500 assorted terminals supplied, with 50 cable ties and insulating tape, in storage case.

Class 2 High voltage insulating rubber floor mat. Essential item required to protect vehicle technicians from the risk of electric shock when working on electric or hybrid vehicles. Independently tested and certified as offering safe protection up to 17kV AC in accordance with BS EN 61111.

Designed for use with a standard multimeter and measures current draw from vehicle components in situ. Suitable for measuring both AC and DC current, without breaking into the circuit. Fitted with 4mm banana connectors and supplied in storage pouch. Powered by 9V battery (supplied). Can also be used with an oscilloscope using a suitable BNC conversion adaptor.

Comprehensive set for easy removal of freewheel alternator pulley, either on or off the vehicle. Allows alternator shaft to be held while pulley retainer is removed.

Designed for use with a standard multimeter and measures current draw from vehicle components in situ. Suitable for measuring both AC and DC current, without breaking into the circuit. Fitted with 4mm banana connectors and supplied in storage pouch. Powered by 9V battery (supplied). Can also be used with an oscilloscope using a suitable BNC conversion adaptor.

12-Function, auto-ranging automotive diagnostic multimeter. Combination digital/bar graph display gives accurate indication of component outputs. Large, easy-to-read high contrast display with bright, white back light. Workshop-tough, durable case with integral stand. Reads standard automotive parameters including duty cycle. Features auto-ranging and data-hold functions with overload...

Tests Zirconia and Titania lambda sensors and ECU. Suitable for 1, 2, 3 and 4 wire sensors, heated and unheated. LED display shows crossover signal from sensor. Simulates rich or lean mixture signals to check ECU response. Insulation-piercing clip for quick and easy connection plus display to confirm wire identity. Features a low battery indicator and powered by 9V battery (supplied).

Fast, accurate and safe current measurement at the fuse box. Ideal for fault-finding on car and commercial vehicle electrical circuits. Includes hold and peak functions for detecting current surges. Features large LCD display with digital and graphical current read-out. Plugs straight into the vehicle's fuse board and supplied with Mini, Standard and Maxi style blade adaptors.

Electrician's gloves suitable for use on hybrid and electric vehicles. Class 0 gloves suitable for working on systems up to 1kV AC in accordance with EN 60903.

Comprehensive kit, suitable for the removal of terminals on most wiring connectors. Reduce time spent on, and damage to, vehicle electrical systems. Features soft grip handles with number identification.

Extra-large, high-contrast LCD display with 36mm high digital read-out and back light. Durable case and integral stand suitable for the toughest workshop conditions. Features millisecond pulse-width function for accurate measurement of fuel injection systems. Includes auto-ranging, data-hold and auto-power-off. Supplied with inductive coupler (IC), test probes, thermocouple and storage case.

Fast and accurate assessment of battery condition, even with the battery partially discharged. No heat, no sparks and no misdiagnosis. Tests battery in accordance with rated output based on SAE, DIN or ENC2 criteria and displays results on LCD screen. Diagnose battery faults at the trade counter, service reception or workshop with confidence. Rugged construction.

Designed for the automotive electrician and conforms to EN 61010 CAT III 600V. Ideal for measuring current draw from vehicle components in situ. Features 10mm clamp. Supplied in pouch. Measures: • AC/DC Voltage • AC/DC Current • Resistance • Audible Continuity • Diode Test.

Professional set of test leads and components suitable for testing and evaluating automotive electronic circuits on modern vehicles. Features 0.7mm back probes ideal for testing vehicle sensors and dual colour LEDs for directional polarity testing. Set includes standard Ø4mm banana style plugs and sockets suitable for use with most diagnostic multimeters and test equipment.

Compact device which accurately tests battery, cranking and alternator. Just key in the battery rating from the top of the battery and results are displayed on an LCD screen. Includes a facility to print results via PC. No internal battery and will test batteries with a residual charge of just 8V. Supplied with PC software and instruction manual in storage pouch.

Save time and money and take the guess-work out of your fault-finding and diagnosis with Autel’s CAN enabled EOBD diagnostic tools. Every technician should have one! They allow the interrogation of the vehicle’s ECU to determine the performance of essential emission-based information, to read and clear Diagnostic Trouble Codes (DTCs) and to obtain vital performance data from the vehicle’s...

Professional quality laser instrument for fast and accurate measurement of rotational speed with or without contact. Will also measure total revolutions, frequency, surface speed and distance. 10 Selectable data set memories each with maximum, minimum and average or single value reading, as appropriate. Supplied with reflective tape, for non-contact measurement, and three heads for contact...